Quantum DLT 8000 Manual Página 384
- Página / 408
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Appendix C: Updating the Firmware
C-4 Quantum DLT 8000 Tape System
When the drive code update is complete, the drive resets, and runs its Power-On
Self Test (POST). The process waits until the tape is reloaded at the beginning
of tape (BOT).
If the firmware image is valid, the tape drive’s PCBA controller’s FLASH
EEPROM is updated with the new firmware image. The WRITE PROTECTED
and TAPE IN USE indicators flash again during the controller firmware update.
C.3 Interpreting the Results of a Firmware Update
Following a firmware update procedure, two possible results can occur:
• The firmware update cartridge is unloaded. This signals a successful update
The tape drive rewinds the cartridge, the door is unlocked, and the green
OPERATE HANDLE indicator illuminates.
• The firmware update cartridge is NOT unloaded. This signals an unsuccessful
update.
The tape drive subsystem may still be usable. Failure may be a result of:
• Power failure
• Bad firmware image on the tape
• Non-functioning FLASH EEPROMS.
Table C—2 provides troubleshooting information.
Table C—2 Results of Firmware Update
If... Then...
The image is valid 1. The FLASH EEPROM containing the current
firmware is erased.
2. The new image is programmed into FLASH
EEPROM (approximately 2 minutes). Then:
• The tape drive resets
• The tape drive runs POST
• The tape drive unloads the tape
cartridge and the cartridge can be
removed. This indicates a successful
firmware update.
- 8000 Tape System 1
- Product Manual 1
- Table of Contents 10
- REVISION HISTORY 27
- Revision History 28
- Quantum DLT 8000 Tape System 28
- ABOUT THIS MANUAL 33
- CONVENTIONS 35
- FOR MORE INFORMATION 35
- READER COMMENTS 35
- About This Manual 36
- Chapter 1 37
- 1.3 SPECIFICATIONS 38
- 1.3.4 Reliability (Projected) 41
- 1.3.5 Physical Specifications 41
- 1.3.7 Operating Air Velocity 43
- 1.3.9 Altitude 45
- 1.3.10 Acoustic Emissions 46
- 1.3.12 Power Requirements 47
- 1.3.13 Current Requirements 48
- TAPE SYSTEM 55
- 2.2.1 Setting the SCSI ID 58
- 2.2.2 Setting TERM PWR 60
- Front Bezel 61
- 2.3.1 Selecting SCSI ID 71
- SCSI Connectors (2) 72
- 220 / 240 V 74
- AC Power Cord Connector 75
- 2.4 The Tape Cartridge 76
- 2.4.4 Loading a Cartridge 82
- 2.4.5 Unloading a Cartridge 84
- 2.5.1 Unload Button 88
- 2.5.3 Selecting Density 89
- 2.9 Troubleshooting 99
- SCSI DESCRIPTION 103
- 3.2 SCSI Commands 104
- SCSI Description 105
- 3.3 Signal States 107
- 3.4 SCSI Signals 109
- 3.4.2 Signal Bus Timing 110
- 3.5 SCSI Bus Phases 113
- Bus Free Sequence 114
- 3.5.2 ARBITRATION Phase 115
- Arbitration Sequence 115
- 3.5.3 SELECTION Phase 116
- Selection Sequence 116
- Selection Time-Out 117
- 3.5.4 RESELECTION Phase 117
- Reselection Sequence 117
- SCSI ID bit 118
- Reselection Time-Out 120
- 3.6 SCSI Bus Conditions 128
- 3.6.2 Reset Condition 129
- 3.6.3 Queued Unit Attentions 130
- Chapter 4 131
- MESSAGES 131
- Messages 132
- 4.2 Supported SCSI Messages 135
- 4.2.12 NO OPERATION (08h) 141
- SCSI COMMANDS 145
- SCSI Commands 146
- 5.1.1 SCSI Pointers 147
- 5.1.3 Status/Error Reporting 151
- (Continued) 153
- 5.3 ERASE Command (19h) 159
- 5.4 INQUIRY Command (12h) 161
- 5.6 LOCATE Command (2Bh) 179
- 5.7 LOG SELECT Command (4Ch) 181
- Page Code Page Description 183
- 02h Write Error Counter Page 183
- 03h Read Error Counter Page 183
- 32h Compression Ratio Page 183
- LOG PAGE HEADER 184
- LOG PARAMETERS 185
- (continued) 186
- 5.8 LOG SENSE Command (4Dh) 189
- Descriptions (continued) 196
- 5.8.5 TapeAlert Page (2Eh) 200
- TAPE ALERT LOG PAGE HEADER 200
- TAPE ALERT LOG PARAMETERS 201
- Descriptions 210
- 5.9.1 Mode Parameter List 217
- 5.9.8 TAPEALERT PAGE (1Ch) 237
- FORCEDENSITY parameter to 4 247
- 5.10.3 MODE SENSE Mode Pages 258
- Data Field Description 284
- 5.14 READ Command (08h) 304
- 5.16.2 Data Mode 311
- 5.16.3 Descriptor Mode 311
- 5.26 REWIND Command (01h) 353
- 5.28 SPACE Command (11h) 360
- 5.30 VERIFY Command (13h) 363
- 5.31 WRITE Command (0Ah) 364
- 5.32.2 Write Data Mode (010b) 368
- INFORMATION 373
- Appendix B 377
- B.2 Bugcheck Packets 378
- B.2.1 POST Failure Packets 379
- B.2.2 Event Log Packets 379
- UPDATING THE FIRMWARE 381
- 1. POST passed 383
- 2. The drive is unloaded 383
- THE LIBRARY PORT 387
- CARTRIDGES 389
- Cartridge 391
- SYSTEM SCSI COMMANDS 397
- DLT 7000 EMULATION FEATURE 399
- SCSI Bus Differences 403
- Front Panel Differences 405
- *81-60118-04 A01* 408
Manuais e produtos relacionados com Unidades de fita magnética Quantum DLT 8000
(38 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.628 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais