Quantum DLT 8000 Manual Página 248
- Página / 408
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
SCSI Commands
5-104 Quantum DLT 8000 Tape System
MODE SELECT Command (6) / (10) (15h) / (55h) (continued)
5.9.10 Changeable Parameters within MODE SELECT
The table below lists the MODE SELECT command’s changeable parameters and their
default, minimum, and maximum values. Descriptions of the various parameters are
provided in the discussions of the different mode pages within MODE SELECT. Note
that parameter rounding is supported for all parameters except for the block descriptor
length.
Table 5–48 Changeable Mode Parameters within MODE SELECT
Page: Parameter Default Minimum Maximum
Header: Buffered Mode, Device Specific Byte 1 0 1
Header: Speed, Device Specific Byte 0 0 3
Block Descriptor Length 08h 00h 08h
Block Descriptor: Block Length
10.0 GB and 20.0 GB Mode
20.0 GB and 40.0 GB Mode
35.0 GB and 70.0 GB Mode
40.0 GB and 80.0 GB Mode
0
0
0
0
0
0
0
0
FFFFFEh
FFFFFEh
FFFFFEh
FFFFFEh
READ / WRITE Error Recovery (01h): PER bit 0 0 1
Control Mode (0Ah): RLEC 0 0 1
Data Compression (0Fh): DCE 1 0 1
Disconnect / Reconnect (02h): Maximum Burst Size 0080h 0000h FFFFh
Disconnect / Reconnect (02h): DTDC 0 0 3
Device Configuration (10h): WRITE Delay Time C8h Fh 1964h
Device Configuration (10h): SEW 1 0 1
Device Configuration (10h): Select Data Compression
Algorithm
1 0 1
- 8000 Tape System 1
- Product Manual 1
- Table of Contents 10
- REVISION HISTORY 27
- Revision History 28
- Quantum DLT 8000 Tape System 28
- ABOUT THIS MANUAL 33
- CONVENTIONS 35
- FOR MORE INFORMATION 35
- READER COMMENTS 35
- About This Manual 36
- Chapter 1 37
- 1.3 SPECIFICATIONS 38
- 1.3.4 Reliability (Projected) 41
- 1.3.5 Physical Specifications 41
- 1.3.7 Operating Air Velocity 43
- 1.3.9 Altitude 45
- 1.3.10 Acoustic Emissions 46
- 1.3.12 Power Requirements 47
- 1.3.13 Current Requirements 48
- TAPE SYSTEM 55
- 2.2.1 Setting the SCSI ID 58
- 2.2.2 Setting TERM PWR 60
- Front Bezel 61
- 2.3.1 Selecting SCSI ID 71
- SCSI Connectors (2) 72
- 220 / 240 V 74
- AC Power Cord Connector 75
- 2.4 The Tape Cartridge 76
- 2.4.4 Loading a Cartridge 82
- 2.4.5 Unloading a Cartridge 84
- 2.5.1 Unload Button 88
- 2.5.3 Selecting Density 89
- 2.9 Troubleshooting 99
- SCSI DESCRIPTION 103
- 3.2 SCSI Commands 104
- SCSI Description 105
- 3.3 Signal States 107
- 3.4 SCSI Signals 109
- 3.4.2 Signal Bus Timing 110
- 3.5 SCSI Bus Phases 113
- Bus Free Sequence 114
- 3.5.2 ARBITRATION Phase 115
- Arbitration Sequence 115
- 3.5.3 SELECTION Phase 116
- Selection Sequence 116
- Selection Time-Out 117
- 3.5.4 RESELECTION Phase 117
- Reselection Sequence 117
- SCSI ID bit 118
- Reselection Time-Out 120
- 3.6 SCSI Bus Conditions 128
- 3.6.2 Reset Condition 129
- 3.6.3 Queued Unit Attentions 130
- Chapter 4 131
- MESSAGES 131
- Messages 132
- 4.2 Supported SCSI Messages 135
- 4.2.12 NO OPERATION (08h) 141
- SCSI COMMANDS 145
- SCSI Commands 146
- 5.1.1 SCSI Pointers 147
- 5.1.3 Status/Error Reporting 151
- (Continued) 153
- 5.3 ERASE Command (19h) 159
- 5.4 INQUIRY Command (12h) 161
- 5.6 LOCATE Command (2Bh) 179
- 5.7 LOG SELECT Command (4Ch) 181
- Page Code Page Description 183
- 02h Write Error Counter Page 183
- 03h Read Error Counter Page 183
- 32h Compression Ratio Page 183
- LOG PAGE HEADER 184
- LOG PARAMETERS 185
- (continued) 186
- 5.8 LOG SENSE Command (4Dh) 189
- Descriptions (continued) 196
- 5.8.5 TapeAlert Page (2Eh) 200
- TAPE ALERT LOG PAGE HEADER 200
- TAPE ALERT LOG PARAMETERS 201
- Descriptions 210
- 5.9.1 Mode Parameter List 217
- 5.9.8 TAPEALERT PAGE (1Ch) 237
- FORCEDENSITY parameter to 4 247
- 5.10.3 MODE SENSE Mode Pages 258
- Data Field Description 284
- 5.14 READ Command (08h) 304
- 5.16.2 Data Mode 311
- 5.16.3 Descriptor Mode 311
- 5.26 REWIND Command (01h) 353
- 5.28 SPACE Command (11h) 360
- 5.30 VERIFY Command (13h) 363
- 5.31 WRITE Command (0Ah) 364
- 5.32.2 Write Data Mode (010b) 368
- INFORMATION 373
- Appendix B 377
- B.2 Bugcheck Packets 378
- B.2.1 POST Failure Packets 379
- B.2.2 Event Log Packets 379
- UPDATING THE FIRMWARE 381
- 1. POST passed 383
- 2. The drive is unloaded 383
- THE LIBRARY PORT 387
- CARTRIDGES 389
- Cartridge 391
- SYSTEM SCSI COMMANDS 397
- DLT 7000 EMULATION FEATURE 399
- SCSI Bus Differences 403
- Front Panel Differences 405
- *81-60118-04 A01* 408
Manuais e produtos relacionados com Unidades de fita magnética Quantum DLT 8000
(38 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.109 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais