Quantum DLT 8000 Manual Página 164
- Página / 408
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
SCSI Commands
5-20 Quantum DLT 8000 Tape System
INQUIRY Command (12h) (continued)
Table 5–8 contains field descriptions for the data returned by the drive.
Table 5–8 Standard Inquiry Data Page — Field Descriptions
Field Name Value Description
Peripheral Qualifier 0 Non-zero if initiator selects an invalid logical unit (see below)
Peripheral Device Type 1 1 indicates that this is a sequential access device (see below).
Note that the Peripheral Device Type entry for a medium
changer is 8.
RMB 1 Removable Medium Bit. Set to 1.
Device Type Modifier 1 Set to 1 to specify a sequential access device.
ISO Version 0 International Standardization Organization Version level. Set
to 0.
ECMA Version 0 European Computer Manufacturers Organization Version
level. Set to 0.
ANSI Version 2 ANSI SCSI Level 2 (SCSI-2) is supported.
AENC 0 Asynchronous Event Notification is not supported.
TrmlOp 0 Terminate I/O Process. The tape drive does not support the
TERMINATE I/O PROCESS message.
Response Data Format 2 This Standard Inquiry Data is in SCSI-2 format.
Additional Length 33h Tape drive uses this field to indicate the number of additional
bytes of INQUIRY Response Data available.
Mchnger - Set to 1 if a Media Changer (Loader) is present and EEPROM
parameter EnbIngMedChgr is set to 1. This SCSI-3 bit
indicates that the Read Element Status and Move Medium
commands can be issued to the drive (LUN0). By default, this
bit is set to 0 on the DLT 8000 drive.
RelAdr 0 Relative Addressing is not supported.
WBus 32 0 Set to 0 since the drive does not support 32-bit transfer.
WBus 16 1 The WBus bit is 1 since the drive supports 16-bit data
transfer.
Sync 1 The drive supports Synchronous Data Transfers.
Linked 1 Linked Commands are supported.
CmdQue 0 The drive does not support Tagged Command Queuing.
SftRe 0 The drive implements the hard reset option in response to
assertion of the SCSI Bus reset line.
Vendor Identification The value in this field is QUANTUM (there is one space after
the word Quantum)
Product Identification The value in this field is DLT8000 (there is no space between
“DLT” and “8000” and one space after “DLT8000”)
- 8000 Tape System 1
- Product Manual 1
- Table of Contents 10
- REVISION HISTORY 27
- Revision History 28
- Quantum DLT 8000 Tape System 28
- ABOUT THIS MANUAL 33
- CONVENTIONS 35
- FOR MORE INFORMATION 35
- READER COMMENTS 35
- About This Manual 36
- Chapter 1 37
- 1.3 SPECIFICATIONS 38
- 1.3.4 Reliability (Projected) 41
- 1.3.5 Physical Specifications 41
- 1.3.7 Operating Air Velocity 43
- 1.3.9 Altitude 45
- 1.3.10 Acoustic Emissions 46
- 1.3.12 Power Requirements 47
- 1.3.13 Current Requirements 48
- TAPE SYSTEM 55
- 2.2.1 Setting the SCSI ID 58
- 2.2.2 Setting TERM PWR 60
- Front Bezel 61
- 2.3.1 Selecting SCSI ID 71
- SCSI Connectors (2) 72
- 220 / 240 V 74
- AC Power Cord Connector 75
- 2.4 The Tape Cartridge 76
- 2.4.4 Loading a Cartridge 82
- 2.4.5 Unloading a Cartridge 84
- 2.5.1 Unload Button 88
- 2.5.3 Selecting Density 89
- 2.9 Troubleshooting 99
- SCSI DESCRIPTION 103
- 3.2 SCSI Commands 104
- SCSI Description 105
- 3.3 Signal States 107
- 3.4 SCSI Signals 109
- 3.4.2 Signal Bus Timing 110
- 3.5 SCSI Bus Phases 113
- Bus Free Sequence 114
- 3.5.2 ARBITRATION Phase 115
- Arbitration Sequence 115
- 3.5.3 SELECTION Phase 116
- Selection Sequence 116
- Selection Time-Out 117
- 3.5.4 RESELECTION Phase 117
- Reselection Sequence 117
- SCSI ID bit 118
- Reselection Time-Out 120
- 3.6 SCSI Bus Conditions 128
- 3.6.2 Reset Condition 129
- 3.6.3 Queued Unit Attentions 130
- Chapter 4 131
- MESSAGES 131
- Messages 132
- 4.2 Supported SCSI Messages 135
- 4.2.12 NO OPERATION (08h) 141
- SCSI COMMANDS 145
- SCSI Commands 146
- 5.1.1 SCSI Pointers 147
- 5.1.3 Status/Error Reporting 151
- (Continued) 153
- 5.3 ERASE Command (19h) 159
- 5.4 INQUIRY Command (12h) 161
- 5.6 LOCATE Command (2Bh) 179
- 5.7 LOG SELECT Command (4Ch) 181
- Page Code Page Description 183
- 02h Write Error Counter Page 183
- 03h Read Error Counter Page 183
- 32h Compression Ratio Page 183
- LOG PAGE HEADER 184
- LOG PARAMETERS 185
- (continued) 186
- 5.8 LOG SENSE Command (4Dh) 189
- Descriptions (continued) 196
- 5.8.5 TapeAlert Page (2Eh) 200
- TAPE ALERT LOG PAGE HEADER 200
- TAPE ALERT LOG PARAMETERS 201
- Descriptions 210
- 5.9.1 Mode Parameter List 217
- 5.9.8 TAPEALERT PAGE (1Ch) 237
- FORCEDENSITY parameter to 4 247
- 5.10.3 MODE SENSE Mode Pages 258
- Data Field Description 284
- 5.14 READ Command (08h) 304
- 5.16.2 Data Mode 311
- 5.16.3 Descriptor Mode 311
- 5.26 REWIND Command (01h) 353
- 5.28 SPACE Command (11h) 360
- 5.30 VERIFY Command (13h) 363
- 5.31 WRITE Command (0Ah) 364
- 5.32.2 Write Data Mode (010b) 368
- INFORMATION 373
- Appendix B 377
- B.2 Bugcheck Packets 378
- B.2.1 POST Failure Packets 379
- B.2.2 Event Log Packets 379
- UPDATING THE FIRMWARE 381
- 1. POST passed 383
- 2. The drive is unloaded 383
- THE LIBRARY PORT 387
- CARTRIDGES 389
- Cartridge 391
- SYSTEM SCSI COMMANDS 397
- DLT 7000 EMULATION FEATURE 399
- SCSI Bus Differences 403
- Front Panel Differences 405
- *81-60118-04 A01* 408
Manuais e produtos relacionados com Unidades de fita magnética Quantum DLT 8000
(38 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.052 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais