Quantum Scalar 100 Guia do Utilizador Página 70
- Página / 126
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
8-60 6-00667-01 Rev B
Scalar 100
2. Use Change to select one of the following:
• DEFAULT — The library reads 6 character barcode labels.
• EXTENDED — The library reads 5 to 13 character barcode labels.
3. Select OK.
Configuring Drive Cleaning
In most configurations, drive cleaning is controlled through the host; however, if desired, the library
has an AutoClean feature that enables the library to control drive cleaning. (Host controlled drive
cleaning is the default condition.)
Drive cleaning requires cleaning cartridges to be imported into the library. (Note that cleaning
cartridges are imported differently than regular tape cartridges.) A total of three cleaning cartridges
can be imported. These cartridges are stored in fixed slots located at the top of columns 2, 4, and
5. These slots are not counted as part of the slot capacity of the library, are not included in the report
of storage elements, and are not addressable to SCSI hosts.
Working with AutoClean
AutoClean allows the library to clean a drive without instruction from a host.
As AutoClean does not require host intervention, it should only be enabled if the host application
does not or is not configured to control drive cleaning. The cleaning operation is transparent to the
host application and will only occur when a drive requests to be cleaned. The host application will
get a delayed response until the cleaning operation is complete.
AutoClean requires at least one cleaning cartridge and a communication interface to the drive with
the ability of the drive to indicate that cleaning is needed. If AutoClean is enabled, the cleaning slots
will be inventoried by touch.
Enabling/Disabling AutoClean
Use AutoClean to enable or disable the AutoClean feature. (Disabling AutoClean will stop all
cleaning inquiries to the drive.) Be sure to import cleaning cartridges into your library before
enabling AutoClean.
Path: Main menu > More > Setup > Library > AutoClean
To enable/disable autoclean
1. From the Main menu, select More. Select Setup and then select Library. Select AutoClean.
NOTE:
A DLT cleaning tape cannot be used in an SDLT drive.
NOTE:
If the Mailbox is configured as storage, the AutoClean function cannot be
enabled.
- Scalar 100 1
- Copyright Notice 2
- Contents 3
- Using the Operator Panel 4
- Running your Library 5
- Configuring your Library 6
- Maintaining your Library 6
- Contents I-v 7
- Troubleshooting and Help 8
- Introduction 11
- Intended Audience 12
- Description 13
- Front Panel Components 14
- Front Power Switch 15
- Door Lock 15
- Operator Panel 15
- Back Panel Components 16
- Rear Power Switch 17
- Remote Management Unit 17
- Storage Networking Controller 17
- Internal Components 18
- Description 2-9 19
- SCSI Connections 20
- Setting up your Scalar 100 21
- Finding a Location 22
- Unpacking your Library 22
- Preparing the Host 24
- Host Coordinate System 25
- Installing a SCSI Adapter 25
- 3-16 6-00667-01 Rev B 26
- Rackmounting your Library 27
- Installing Side Panels 30
- Installing Casters 31
- Installing/Removing a Drive 31
- Removing a Drive 32
- Replacing a Drive 33
- Installing Bulk Load Mailbox 34
- Removing the Standard Mailbox 35
- Installing a Storage Column 38
- 4-30 6-00667-01 Rev B 40
- Working with Buttons 44
- Getting Library Messages 44
- Getting Mailbox Status 45
- Menu Guidelines 47
- Using the Main menu 47
- The Menu Tree 48
- Getting Information 49
- Getting Sensor Information 51
- Getting Slot Information 52
- Viewing Drive Information 55
- Getting Logs 55
- Printing Logs (HyperTerminal) 56
- Getting the Command Logs 56
- Getting Error Logs 57
- Getting Drive Logs 57
- Moving the Picker 60
- Taking Inventory 61
- CAUTION: 62
- Importing Tape Cartridges 63
- Exporting a Tape Cartridge 64
- Importing Cleaning Cartridges 65
- Working with Drives 66
- Configuring Barcode Length 69
- Configuring Drive Cleaning 70
- Setting Drive SCSI IDs 71
- Setting the Date and Time 71
- Locking/Unlocking the Mailbox 73
- 8-64 6-00667-01 Rev B 74
- Updating Drive Firmware 76
- Exercising the Picker Fingers 77
- Exercising the Picker Axes 79
- Exercising the Library 80
- Running a Demo 81
- Running a Self Test 81
- Resetting a Drive 82
- Servicing Drives 83
- 9-74 6-00667-01 Rev B 84
- Tape Use Guidelines 85
- Using Barcode Labels 86
- 10-78 6-00667-01 Rev B 88
- Starting the RMU 90
- Supported Browsers 90
- RMU Requirements 90
- Setting up the RMU 90
- Logging into the RMU 91
- Configuring SNMP 92
- Configuring RMU User Accounts 93
- Configuring the Time and Date 94
- Updating Firmware 94
- Viewing Diagnostic Files 95
- Viewing Logs 95
- Getting Help 96
- Operator Information Messages 110
- Interpreting Drive LEDs 111
- Getting More Information 111
- 12-102 6-00667-01 Rev B 112
- Specifications 113
- SDLT/DLT 114
- 13-106 6-00667-01 Rev B 116
- Regulatory Notices 117
- IC Notice (Canada Only) 118
- CE Notice 119
- VCCI Notices (Japan Only) 119
- Declaration of Conformity 120
- 15-112 6-00667-01 Rev B 122
- Index 15-113 123
- 15-114 6-00667-01 Rev B 124
- Index 15-115 125
Manuais e produtos relacionados com Bibliotecas de fitas e autoloaders Quantum Scalar 100
(16 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.064 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais