Quantum 1200 Series DAT Autochanger Guia do Utilizador Página 141
- Página / 294
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
SDLT 600 SCSI Interface Guide Chapter 4: SCSI Commands
81-81200-02 REV A01 January 2005 4-99
DefSEW Binary 1 1 Default Synchronize at Early
Warning parameter.
DisDeferClnRpt Binary 0 1 When set to 1, the drive sends a
cleaning report over the library port
as soon as the cleaning light
illuminates. When set to 0, the drive
sends the report only at unload.
DisUnbufMode Binary 0 1 When set to 1, the drive completely
disables unbuffered mode; it ignores
the MODE SELECT buffered mode
selection to turn off buffered mode.
When set to 0, buffered mode can
be enabled or disabled.
EnablePPRMsg ASCII 0 1 Not used.
EnaCleanLib Binary 1 1 When set to 1, the drive reports
cleaning status using the library
tape drive interface. When set to 0,
this functionality is disabled.
EnaCleanLight Binary 1 1 When set to 1, the Cleaning
Required LED is turned on and off
as appropriate. When set to 0, this
functionality is disabled.
EnaCleanSense Binary 1 1 When set to 1, the drive collects
cleaning Sense Key data. When set
to 0, this functionality is disabled.
EnaCleanTA Binary 1 1 When set to 1, the drive returns tape
cleaning flags for TapeAlert. When
set to 0, this functionality is
disabled.
EnaGranularity Binary 1 1 Enables the Granularity field in the
READ BLOCK LIMITS command.
EnaInitSyncNeg Binary 0 1 When set to 1, enables target-
initiated synchronous negotiation.
EnaModePg22 Binary 0 1 Enable vendor-specific data
compression (Status Mode Page).
EnaModePg3C Binary 1 1 Enable Disaster Recovery Mode
(Page 3Ch).
Table 4-58. EEPROM Vendor Specific MODE SELECT Page — Parameter Descriptions
Parameter Name
Data
Type
Default
Length
(Bytes)
Usage
- 6'/7 1
- Table of Contents 3
- List of Tables 9
- List of Figures 15
- Introduction 21
- 1.3 Related Documents 22
- 1.4 Structure of this Manual 22
- 1.5 Conventions 23
- 1.6 For More Information 23
- 1.7 Reader Comments 24
- SCSI Parallel Protocol 25
- 2.3.1 Attention Condition 26
- RESET or DISCONNECT message 27
- 2.3.2 Reset Condition 28
- SCSI Messages 29
- 3.2 Supported SCSI Messages 31
- 3.2.1 ABORT TASK SET (06h) 32
- 3.2.2 TARGET RESET (0Ch) 33
- 3.2.3 TASK COMPLETE (00h) 33
- 3.2.4 DISCONNECT (04h) 33
- 3.2.5 IDENTIFY (80h - FFh) 34
- 3.2.10 MESSAGE REJECT (07h) 37
- 3.2.11 NO OPERATION (08h) 37
- WRITE BUFFER 3Bh Page 4-249 45
- 4.1.4 Behavior at Power-On 49
- 4.2 SCSI Command Descriptions 50
- 4.3 ERASE Command (19h) 52
- 4.4 INQUIRY Command (12h) 53
- Unit Serial Number Page (80h) 62
- • Logical Unit NAA Identifier 63
- Logical Unit NAA Identifier 66
- 4.5 LOAD UNLOAD Command (1Bh) 70
- 4.6 LOCATE Command (2Bh) 72
- 4.7 LOG SELECT Command (4Ch) 73
- 4.8 LOG SENSE Command (4Dh) 81
- Log Page” on page 4-43 90
- 0000h – 000Fh) 104
- — Field Descriptions 108
- SDLT 600 109
- SCSI Interface Guide 109
- SCSI Commands 109
- 81-81200-02 109
- 4.9.1 Mode Parameter List 111
- Mode Parameter Header 113
- SDLT tape drive 116
- Mode Page Descriptor 117
- 4.9.10 TapeAlert Page (1Ch) 134
- 4.10.3 MODE SENSE Mode Pages 155
- Control Mode Page (0Ah) 160
- Data Compression Page (0Fh) 162
- Medium Partition Page (11h) 167
- Port Control Page (19h) 169
- Parameter List 176
- Command (1Eh) 194
- 4.14 READ Command (08h) 195
- ATTRIBUTE LIST Service Action 202
- VOLUME LIST Service Action 203
- PARTITION LIST Service Action 204
- Attributes 205
- Attribute Identifier Values 207
- AND DEVICE 209
- Field Descriptions 212
- Standard Host Type Attributes 219
- Value Meaning 220
- 00h No code specified (ASCII) 220
- 01h - FFh Reserved 220
- 3C 03 A2 00 00 00 00 00 04 80 228
- 4.17.3 Data Mode (02h) 229
- 4.17.4 Descriptor Mode (03h) 229
- Command (A3h) 250
- Descriptions 251
- FUNCTIONS Command (A3h) 256
- 4.30 REWIND Command (01h) 274
- 2. Rewinds the tape 276
- 4. Rewinds the tape 276
- RESULTS command 277
- 4.33 SPACE Command (11h) 281
- 4.35 VERIFY Command (13h) 284
- 4.36 WRITE Command (0Ah) 285
- Exception Conditions 286
- 4.38.2 Write Data Mode (02h) 292
Manuais e produtos relacionados com Software Quantum 1200 Series DAT Autochanger
Software Quantum SuperLoader 3 Guia do Utilizador
(160 páginas)
(160 páginas)
Software Quantum SuperLoader Guia do Utilizador
(196 páginas)
(196 páginas)
Software Quantum Scalar i2000 Guia do Utilizador
(544 páginas)
(544 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.026 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais