Quantum Scalar 1000 Guia do Utilizador Página 78
- Página / 122
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
70 Configuring Channels and Devices
Resetting the Fibre Channel
Using the Reset command cancels all pending commands, resets the channel, and performs a rescan. Use
this command after making changes to the channel configuration.
1 Expand the appliance in the navigation panel or the graphical panel.
2 Right-click the appropriate Fibre Channel graphic.
3 Select Reset.
A warning is displayed.
4 Select Yes to continue.
The following message is displayed in the Status/Message Area:
Resetting Fibre Channel n on xxx.xxx.xxx.xxx. Please wait several minutes before doing a ‘Refresh.’
In this example, the “n” represents the Fibre Channel number and xxx.xxx.xxx.xxx represents the IP
address of the appliance.
Configuring the Fibre Channel
Fibre Channel parameters you can set are host type, loop ID, frame size, connection type, and port mode.
1 Log on as SAN administrator, portal administrator, or power user.
2 Expand the appliance in the navigation panel or the graphical panel.
3 Right-click the appropriate Fibre Channel graphic.
4 Select Configure.
The Fibre Channel Parameters dialog box is displayed.
5 Use the drop-down boxes and check boxes to make changes to the configuration as necessary. Refer
to U
nderstanding Port Mode Options on page 71 and Understanding Connection Type Options on page
71.
6 When you are finished viewing or setting Fibre Channel parameters, select OK to continue.
A warning is displayed.
7 Select Yes to proceed with the Reset.
The following message posts in the Status/Message Area:
Resetting Fibre Channel n on xxx.xxx.xxx.xxx. Please wait several minutes before doing a ‘Refresh.’
In this example, the “n” represents the Fibre Channel number and xxx.xxx.xxx.xxx represents the IP
address of the appliance.
CAUTION
Use Reset carefully because it causes pending I/O commands to
return failed status back to the host operating system and may have
unexpected results. Make sure all I/O is stopped before issuing this
command. For instructions on doing so, refer to the appliance’s
Hardware User Guide.
Note
Basic users are not authorized to configure Fibre Channels.
CAUTION
If you change any of the Fibre Channel parameter settings, you must
reset the channel or reboot the appliance to use the new settings.
- User’s Guide 1
- 89558 Böhmenkirch 2
- Contents 3
- 6 Managing User Accounts 39 5
- 7 Working with Portals 43 5
- 11 Configuring SAN Access 75 6
- 12 Troubleshooting the SAN 93 6
- A Glossary 107 7
- Description 11
- Using the SAN Client 12
- Event Logging 12
- 6 Description 14
- 8 Description 16
- Getting Started 17
- Before Installing AMC 18
- Installing the AMC Server 19
- 12 Getting Started 20
- Launching the AMC Server 21
- Installing the AMC Client 22
- Launching the AMC Client 23
- Connecting to the Server 24
- Logging on 25
- Logging off 26
- Exiting the AMC Client 27
- Shutting Down the AMC Server 27
- 20 Getting Started 28
- Frequently Asked Questions 29
- 22 Frequently Asked Questions 30
- How do I create policies? 31
- 24 Frequently Asked Questions 32
- The SAN Management Interface 33
- Received Event Trap Window 34
- Scalar i2000 38
- Device Numbering 40
- Graphical Panel 40
- Data Panel 41
- Max Speed 42
- Status/Message Area 43
- Common SAN Management Options 44
- Managing User Accounts 47
- 40 Managing User Accounts 48
- Adding a New User Account 49
- Modifying a User Account 50
- Deleting a User Account 50
- Working with Portals 51
- Modifying a Portal 52
- Deleting a Portal 53
- 46 Working with Portals 54
- Working with SAN Categories 55
- Creating a new Category 56
- Renaming a Category 56
- Deleting a Category 56
- Moving a Category 57
- Moving Items by Drag and Drop 57
- Working With Views 59
- Opening Saved Views 60
- Creating Views 60
- Saving Views 62
- Deleting Views 62
- Searching the Current View 62
- Reporting the Current View 63
- Configuring Email 65
- Configuring Policies 66
- Discovering the SAN 67
- Rediscovering a Segment 68
- Managing the SAN Appliance 69
- Refreshing Data 70
- Updating Firmware 72
- Using Restart 72
- Displaying RMU Data 73
- Managing the SCSI Channel 75
- Configuring the SCSI Channel 76
- Managing the Fibre Channel 77
- Resetting the Fibre Channel 78
- Configuring the Fibre Channel 78
- Managing a Device 80
- Editing Device Maps 81
- Pre-Assigning Device Numbers 82
- Configuring SAN Access 83
- Using Channel Zoning 84
- Data Mover Module 84
- Installing HRS 85
- 78 Configuring SAN Access 86
- 80 Configuring SAN Access 88
- Installing SFM 89
- 82 Configuring SAN Access 90
- Adding SFM Hosts 91
- Using eVPS 92
- Installing eVPS 93
- 86 Configuring SAN Access 94
- 88 Configuring SAN Access 96
- Deleting eVPS Hosts 97
- Using the eVPS View Menu 97
- Using VPM 98
- Making VPM assignments 99
- 92 Configuring SAN Access 100
- Troubleshooting the SAN 101
- Interpreting the Event Log 102
- 96 Troubleshooting the SAN 104
- Receiving Event Traps 105
- Monitoring the LED Panel 106
- Figure 21 SNC 4000 LED panel 107
- Figure 22 SNC 5100 LED panel 107
- Using Identify 108
- Monitoring Environmental Data 109
- Using Health Check 110
- Obtaining a Drive Dump 111
- Checking the Command Flow Log 112
- 106 Troubleshooting the SAN 114
- Glossary 115
- 108 Glossary 116
- 110 Glossary 118
- 112 Index 120
- 114 Index 122
Manuais e produtos relacionados com Software Quantum Scalar 1000
Software Quantum DX30 Guia do Utilizador
(58 páginas)
(58 páginas)
Software Quantum SuperLoader 3 Guia do Utilizador
(160 páginas)
(160 páginas)
Software Quantum SuperLoader Guia do Utilizador
(196 páginas)
(196 páginas)
Software Quantum Scalar i2000 Guia do Utilizador
(544 páginas)
(544 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.038 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais