Quantum TC2201 Guia do Utilizador Página 98
- Página / 164
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Perform Configuration
Quantum TC2201 User’s Guide 78
1 Select X Return to previous menu
2 Select A Save Configuration
3 Select X Return to previous menu
4 Select 4 Reboot
After the TC2201 finishes rebooting, the Main Menu will appear on the
serial port but, for Telnet, a new session will need to be opened to
continue configuring the TC2201. DHCP status can be verified from the
Ethernet Configuration Menu where DHCP Configuration is indicated as
“Enabled” if DHCP has been successfully activated. Note that the IP
address may also appear different than the former non-DHCP IP address.
Your DHCP server may allow you to set up a lease reservation for an IP
address by providing the server with the Ethernet MAC address of the
TC2201. This sets the DHCP server to always provide the same IP address
to the TC2201. This setup can be useful for remote management of the
TC2201 via Telnet or Visual Manager. Because the method of setting up a
lease reservation varies depending on the DHCP server being used, it is
recommended you contact your Network Administrator for assistance.
For more information about configuring DHCP, see Appendix D of this
manual.
•Select 2 to change the IP address of the TC2201. The default setting
for the Ethernet port is 1.1.1.1. The default setting for iSCSI Port 0 is
169.254.1.1. The default setting for iSCSI Port 1 is 169.254.1.2.
•Select 3 to change the IP subnet mask for the TC2201. The default for
this setting is 255.255.255.0.
•Select 4 to change the gateway for the Ethernet network of the
TC2201.
•Select 5 to change the Ethernet physical address, or MAC address, of
the TC2201. Ethernet physical addresses are always assigned to
Ethernet adapters by the manufacturers.
Note: To use the DHCP feature, a DHCP server must be operational on the
Ethernet network used by the TC2201. If the DHCP feature is used
when there is no DHCP server, the standard for DHCP requires that
the TC2201 wait three minutes for a response from a DHCP server
before timing out.
- 7& 1
- Contents 3
- Chapter 3 Troubleshooting 56 5
- Glossary 138 7
- Quantum TC2201 User’s Guide x 10
- Customer Support 0 20
- Introduction 21
- Operation Indicators 1 22
- How the TC2201 Works 1 23
- Processing SCSI Information 1 23
- Chapter 1 Introduction 24
- Processing SCSI Information 24
- Quantum TC2201 User’s Guide 4 24
- LAN-free Backup and Restore 1 25
- TC2201 Features 1 26
- TC2201 Benefits 1 27
- TC2201 Specifications 1 28
- TC2201 Specifications 29
- Quantum TC2201 User’s Guide 9 29
- TC2201 Web Interface 30
- TC2201 bridge 31
- Main menu 31
- Status information 31
- Home Page 2 32
- System Page 2 33
- Ethernet Page 2 42
- SCSI Bus Page 2 47
- Discovery Page 2 52
- Statistics Page 2 58
- Utilities Page 2 59
- Utilities Page 63
- Figure 31 Advanced trace 63
- Figure 40 SCSI Command 72
- Tracking Page 72
- Features 2 73
- Report 2 74
- Reboot 2 75
- Troubleshooting 76
- Chapter 3 Troubleshooting 77
- Indicators 77
- Figure 44 TC2201 LEDs 77
- Basic Verification 3 78
- Basic Verification 79
- 3-Pin to DB-9 Serial Pin 81
- Assignments 81
- Figure 45 Corresponding Pin 82
- Outs of DB-9 Connector 82
- 1 23456 7 84
- Inband SCSI-3 85
- Commands 85
- General Commands 2 86
- General Commands 89
- Quantum TC201 User’s Guide 69 89
- Vendor Unique Commands 2 90
- Using the Command Line 91
- Interface 91
- Power Up Messages 3 92
- Power Up Messages 93
- Table 8 Main menu 93
- Perform Configuration 3 94
- Table 10 User 95
- Settings Configuration 95
- Table 13 Change 99
- DNS Settings Menu 99
- Perform Configuration 100
- Table 14 iSCSI 100
- Configuration Menu 100
- Table 15 Authentication 101
- CHAP Records 101
- Table 17 iSCSI Portal 103
- Group Configuration 103
- Table 23 Select 111
- Current Map 111
- Table 24 Add a Map 112
- Table 27 Edit Map 114
- Table 30 Deleting an Entry 116
- Table 34 iSCSI Host 119
- Table 36 Adding a 121
- Table 37 Deleting a 122
- Mapping Main Menu’ 123
- Table 39 Utility 125
- Settings 125
- Table 40 Trace 126
- Table 41 Trace 127
- Settings, Page 2 127
- Table 42 Trace 128
- Settings, Page 3 128
- Table 43 Trace 129
- Settings, Page 4 129
- Table 44 Trace 130
- Settings, Page 5 130
- Table 45 Event Filter 131
- Table 46 System 132
- Clock Setup Menu 132
- System Utilities 3 133
- System Utilities 135
- Table 50 SCSI 135
- Device Display Menu 135
- Table 51 SCSI 136
- Resource Display 136
- Table 52 Event Log 137
- Reboot 3 140
- Table 56 Advanced 141
- Licensed Features 141
- Table 57 Download 142
- Firmware Menu 142
- Using the FTP Interface 143
- Update Firmware 4 147
- How to Change Block 148
- Figure 48 Registry Editor 150
- Figure 50 Netvault Device 153
- Management 153
- Procedure G: CommVault Galaxy 155
- Figure 51 HP Data Protector 155
- (Advanced Options) 155
- Figure 52 CommVault Galaxy 156
- Figure 53 CommVault Galaxy 157
- (Advanced Tab) 157
- Glossary 158
- View Port Name 164
Manuais e produtos relacionados com Redes Quantum TC2201
Redes Quantum Tape Drive SDLT 600A Manual
(8 páginas)
(8 páginas)
Redes Quantum PX502 Guia do Utilizador
(14 páginas)
(14 páginas)
Redes Quantum 560UF/L Manual do Utilizador
(45 páginas)
(45 páginas)
Redes Quantum DAT 160 Guia do Utilizador
(64 páginas)
(64 páginas)
Harbor Freight Tools 38160 manuales
Manuales del propietario y guías del usuario para Herramientas Eléctricas Harbor Freight Tools 38160.
Ofrecemos 1 manuales en pdf Harbor Freight Tools 38160 para descargar gratis por tipos de documentos: Manual de usuario
Comentários a estes Manuais